Menu Close

How do I know if my outboard water pump is bad?

Jim Brown

How do I know if my outboard water pump is bad?

How to Tell if a Water Pump Is Bad

  1. The outboard motor is overheating.
  2. The impeller is living on borrowed time.
  3. There is a reduced stream of water from the cooling water outlet.

How do you change a water pump on a Johnson 50 hp outboard?

Remove the Old Water Pump

  1. Remove the Johnson lower unit from the boat.
  2. Remove the water pump’s mounting bolts.
  3. Remove the O-ring from the drive shaft.
  4. Remove the water pump case.
  5. Check for sand, dirt and debris in the power head, and flush it out if necessary.
  6. Use a screwdriver to remove the impeller.

How do you test an outboard water pump?

How Do You Test an Outboard Water Pump? On many outboards, you can simply put on the muffs and start the engine. You should see a steady stream of water coming out of the holes on the top of the engine. However, some brands do pump out a stream, but it might not look steady.

Why does my outboard motor not pump water?

The water pump impeller is the cause of most water circulation and overheating problems. The impeller is essentially a small, round disc with spinning blades used to move water through the circuit of the outboard motor. When the impeller is broken, it stops the supply of water to the engine and results in overheating.

How often should you change your outboard water pump?

It’s good outboard maintenance practice to check your water pump impeller every season, and replace it every two to three seasons. 300 hours of use or every 3 years whichever comes first!

How often should you change water pump impeller?

Most mechanics and manufacturers recommend every 3 years more because you don’t want the bolts on your lower unit to cease up more than the actual wear to the impellor.

How often should you change the water pump on an outboard motor?

How to replace a Johnson 50 hp water pump?

Here’s how to replace a Johnson 50 HP water pump: Before you can start the installation process, you’ve got to remove the defunct water pump. Remove the Johnson lower unit from the boat. Remove the water pump’s mounting bolts. Remove the O-ring from the drive shaft. Remove the water pump case.

How does a Johnson 15HP outboard water pump work?

The 15-horsepower Johnson outboard motor uses a raw water cooling system. This means that the sea, lake or river water in which you’re boating is drawn into the motor through an intake on the lower unit and pumped throughout the power head by the water pump located atop the lower unit.

How often should I replace my outboard water pump?

As a general rule of thumb, the water pump impeller should be replaced every other season. A water pump repair kit is available for almost all outboard models. For steps requiring lubrication use BRP Triple-Guard Marine Grease or Mercury 2-4-C Marine Lubricant. Remove the bolts that attach the lower unit to the midsection

How to fix a Johnson Evinrude water pump?

1 Check that the water tubes are clean and free from obstructions 2 Coat the water tube pickup grommets with lubricant 3 Mate the lower unit with the upper exhaust housing making sure the drive shaft goes in it proper guide hole and simultaneously guide the water tube into the rubber

How do I know if my outboard water pump is bad?

Jim Brown

How do I know if my outboard water pump is bad?

How to Tell if a Water Pump Is Bad

  1. The outboard motor is overheating.
  2. The impeller is living on borrowed time.
  3. There is a reduced stream of water from the cooling water outlet.

How much does it cost to replace a water pump on a Mercury outboard?

The average cost for a Mercury Mariner water pump replacement is between $355 and $401. Labor costs are estimated between $176 and $222 while parts are priced at $179. This range is based on the number and age of Mercury Mariner’s on the road.

How often should you change water pump on Mercury outboard?

Mercury recommends changing the impeller every 300 hours…its in the owners manual. It’s an easy enough job to do yourself if you have some mechanical skills.

How often should you change your outboard water pump?

It’s good outboard maintenance practice to check your water pump impeller every season, and replace it every two to three seasons. 300 hours of use or every 3 years whichever comes first!

How do you test an outboard water pump?

How Do You Test an Outboard Water Pump? On many outboards, you can simply put on the muffs and start the engine. You should see a steady stream of water coming out of the holes on the top of the engine. However, some brands do pump out a stream, but it might not look steady.

How often should you replace water pump on outboard?

How much does it cost to change water pump on outboard motor?

The average water pump replacement cost is $550, with prices ranging from $461 to $638 in the US in 2020. But typically depends on the type of vehicle you drive and the auto repair shop you take it to. Labor costs are between $256 and $324 while parts cost between $205 and $314.

How often should you replace outboard thermostat?

Typically, water pumps and thermostats should be serviced every two to three years. This varies on where you do most of your boating.

How often should you change water pump impeller?

Most mechanics and manufacturers recommend every 3 years more because you don’t want the bolts on your lower unit to cease up more than the actual wear to the impellor.

How do you remove water pump from Mercury outboard motor?

Shift the engine into forward gear. Tilt the motor up, using its trim-tilt system. This gives you room to remove the lower unit, the bottom part of the motor. You won’t have to bend over to remove the unit and you’ll have room for a second person to support it during removal.

How to change the water pump on a 1997 force outboard?

The water pump in your Force outboard takes on a lot of wear and tear, and as such, requires regularly replacement. The water pump draws in water and circulates it through the engine to keep it cool. Loosen the fasteners that hold the lower unit of your motor to the upper unit. Grab the lower unit and set it down where you will be working on it.

How does a water pump work on an outboard motor?

As you remove the two bolts, have your helper support the unit. Slide the lower unit straight away from the outboard. The water tube, which moves water from the water pump to the rest of the motor, will pull loose from the top of the pump housing on the top of the lower unit. Move the lower unit to the workbench.

How do you change a water pump motor?

Align the water pump face plate and hand-thread the four retaining bolts to get them started. Tighten them with the socket set. Lift the lower unit and replace it to the bottom of the motor. Hold it in place while you hand start the retaining bolts. Tighten them with your socket set.

How do I know if my outboard water pump is bad?

Jim Brown

How do I know if my outboard water pump is bad?

How to Tell if a Water Pump Is Bad

  1. The outboard motor is overheating.
  2. The impeller is living on borrowed time.
  3. There is a reduced stream of water from the cooling water outlet.

How often should you change a water pump on an outboard motor?

It’s good outboard maintenance practice to check your water pump impeller every season, and replace it every two to three seasons. 300 hours of use or every 3 years whichever comes first!

How do you test an outboard water pump?

How Do You Test an Outboard Water Pump? On many outboards, you can simply put on the muffs and start the engine. You should see a steady stream of water coming out of the holes on the top of the engine. However, some brands do pump out a stream, but it might not look steady.

How much does it cost to replace a boat water pump?

The average cost for a Water Pump Replacement is between $355 and $401 but can vary from car to car.

Why does my outboard motor not pump water?

The water pump impeller is the cause of most water circulation and overheating problems. The impeller is essentially a small, round disc with spinning blades used to move water through the circuit of the outboard motor. When the impeller is broken, it stops the supply of water to the engine and results in overheating.

How often should you replace outboard thermostat?

Typically, water pumps and thermostats should be serviced every two to three years. This varies on where you do most of your boating.

How long can you run an outboard motor without water?

How Long Can an Outboard Run Without Water? An outboard motor’s water pump will be damaged in as little as a few seconds without a water source. Depending on the size of the outboard engine itself and ambient temperatures, it may be able to go a few minutes without damage.

Why is my outboard not pumping water?

There are three reasons your outboard motor’s impeller won’t pump. The first is that the water stream fitting — the outlet hole for an outboard motor’s cooling system — is clogged. The second is that the water inlets are clogged; no water is getting to the pump, so it isn’t pumping.

How do you remove a outboard water pump?

Remove the bolts that attach the lower unit to the midsection Not all shift rods disconnect in the same way. Some disconnect up by the powerhead, some disconnect below the swivel bracket, and some disconnect above the gearcase. Remove the water pump housing and impeller from gearcase

How often should I Change my outboard water pump impeller?

boats.com Senior Editor, Lenny Rudow, walks us through the steps on how to change your outboard engine water pump impeller. It’s good outboard maintenance practice to check your water pump impeller every season, and replace it every two to three seasons.

How to replace an outboard water pump gearcase?

Remove the water pump housing and impeller from gearcase Also remove the wear plate and gaskets from the gearcase Install new water pump wear plate and gaskets on gearcase Install impeller so that it lines up with impeller key Turn driveshaft as you place the housing on top of the impeller.

Where does the water come from on an outboard water pump?

Inside the pump housing, there is a rubber impeller that is keyed to the driveshaft. As water enters into the lower gear case via the inlets on the side of the lower unit, the driveshaft will turn the pump impeller. This pump then draws water from the intakes into the housing.