Menu Close

How do I fix error code E02 on a lazy spa?

Jim Brown

How do I fix error code E02 on a lazy spa?

Please follow these steps to resolve this:

  1. Remove the spa pump from the liner, with the stopper caps placed on the inside.
  2. Empty the spa fully of water.
  3. Remove the stopper caps and place a hose on the inside of the spa, up against the debris screen.
  4. Complete this for 5 minutes on each debris screen.

What does EO2 mean?

EO2

Acronym Definition
EO2 Equipment Operator Second Class (Naval Rating)
EO2 Engineering Aide Second Class (Naval Rating)

How do I reset my lazy spa E02?

Pump needs to be reset.

  1. Watch the Thermal Reset Video.
  2. Turn the pump unit on at the mains.
  3. Press the test button once and leave it bleeping (leave for 10 seconds).
  4. Turn the pump unit off and unplug from the socket (leave for 10 seconds).
  5. Plug the pump unit back in and turn it back on.

What does E2 mean on a hot tub?

The E2 Error Code has been implemented to indicate when the Portable Control Unit (PCU) senses a fault with the temperature sensors. This fault may be a worn sensor, corroded connection or wiring.

Why does my lazy SPA says E02?

The E02 error code can occur when the filters are dirty or blocked. KINKED OR BENT LINER PIPES.

Where is the reset button on my lazy spa?

How do you reset a lazy spa?

  1. Plug back in and switch on. Then wait 10 seconds. [
  2. Press the test button once and leave it beeping for. [ 01:19]
  3. Turn off plug and remove from socket then wait 10 seconds. [ 01:27]
  4. Fully depress the thermal reset button. This is found on the side of the pump next to a yellow sticker. [

Why does my Lay-Z-Spa keep switching off?

Why does the spa switch off after 72 hours? This is a safety function. In order to reactivate the spa simply unlock the control panel by holding the lock/unlock key and then pressing the heater function.

Why does my lazy spa says E02?

Why does my Lay Z Spa keep switching off?

Why is my hot tub flashing error?

Hot tub temperature sensor has detected an unsafe water temperature and the heater shuts off. The water probably isn’t flowing fast enough through the heater causing the temperature to increase. DO NOT USE THE HOT TUB while these error codes are flashing as the water will be scalding hot.

What does EO2 mean on Lazy Spa hot tub?

The EO2 error can affect all AirJet™ and HydroJet™ Lay-Z-Spa hot tubs. There are a number of causes which can be fixed quickly and easily. Cause 1: Dirty filter. A dirty water filter can cause water flow issues resulting in an EO2 error. Click to see full answer.

What is the lazy spa error code E02?

If you are curious about what is Lazy Spa E02 and how to fix Lazy Spa Error Code E02? Here is your answer This is an error code which displays on the control panel of Lay z Spa due to lay z spa pump problems. Here are some common Reasons Why Lazy Spa E02 And Lazy Spa E08 occur:

How to fix an EO2 error on Lay z spa?

Reset, test, reset (If your pump has a have PRCD). Step 3: If there is a kink or bend, try to manipulate them out. Step 4: Restart pump. Reset, test, reset (If your pump has a have PRCD). Step 4: Restart pump. Reset, test, reset (If your pump has a have PRCD).

What causes an EO2 error on a hydrojet Airjet hot tub?

The EO2 error can affect all AirJet™ and HydroJet™ Lay-Z-Spa hot tubs. There are a number of causes which can be fixed quickly and easily. Cause 1: Dirty filter. A dirty water filter can cause water flow issues resulting in an EO2 error.

https://www.youtube.com/watch?v=NtAnfS65jnA

How do I fix error code E02 on a lazy spa?

Jim Brown

How do I fix error code E02 on a lazy spa?

Please follow these steps to resolve this:

  1. Remove the spa pump from the liner, with the stopper caps placed on the inside.
  2. Empty the spa fully of water.
  3. Remove the stopper caps and place a hose on the inside of the spa, up against the debris screen.
  4. Complete this for 5 minutes on each debris screen.

How do I reset my lazy spa E02?

Pump needs to be reset.

  1. Watch the Thermal Reset Video.
  2. Turn the pump unit on at the mains.
  3. Press the test button once and leave it bleeping (leave for 10 seconds).
  4. Turn the pump unit off and unplug from the socket (leave for 10 seconds).
  5. Plug the pump unit back in and turn it back on.

How do you fix the code on a hot tub?

DR or DRY Error Message Like FLO issues, this can commonly be fixed by topping off your hot tub water level. DR or DRY will show up if there is little to no water travelling through your heater.

How do I reset my hot tub heater?

How Do I Reset My Hot Tub Heater?

  1. Turn off the power to your hot tub at the breaker.
  2. Find your hot tub’s red high limit reset button, which may be on the heater itself covered by rubber.
  3. Next, press the red reset button, which will make a clicking sound when it has been reset.

What does EO2 mean?

EO2

Acronym Definition
EO2 Equipment Operator Second Class (Naval Rating)
EO2 Engineering Aide Second Class (Naval Rating)

What does E03 mean on hot tub?

AMBIENT AIR TEMPERATURE
E03 ERROR CODE AMBIENT AIR TEMPERATURE. REASON, THE TEMPERATURE IS TOO LOW. This error code is visible if the ambient air temperature is too low outside. The spa pump will not run if the air temperature is below 4-6°c.

Why does my hot tub keep shutting off?

So, why does my hot tub keep tripping and turning off? The problem could be due to a worn GFCI breaker, moisture or corrosion inside the breaker box, damaged or loose wiring, or malfunctioning components. It could even be down to a bad heating element or a flooded blower.

Why does my hot tub keep beeping?

Have you changed your filter recently? A dirty filter will block the water from circulating your filter housing and a safety cut off valve will kick in to avoid breaking the pump displaying warning E02. This is one of the main causes of the alarm being set off.

Where is the reset button on my hot tub?

The reset button is located in the equipment compartment. Plug the spa back into the power source. Check the circulation pump if the spa does not heat while jets and lights are working. This may be caused by the circulation pump thermal cut-off being tripped.

What does E02 mean on a hot tub?

E02 After starting or during the functions of filtering or/and heating, the water flow sensors do not detect water flow. 1. The 2 stopper caps have not been removed from inside the spa. Remove the filter set from inside the spa and push the filter or heat button. What does e03 mean on hot tub? E03 means that the water temperature is lower than 4ºC.

Why do I get the E02 error on my Coleman water pump?

If you try to start your water pump with no water in the tub or with the water level below the filter inlets, you will get this error. This only makes sense since the E02 error indicates a problem with water flow. If there is no water there, it cannot flow.

Why is my Coleman lazy spa E02 not working?

Here are some common Reasons Why Lazy Spa E02 And Lazy Spa E08 occur: You might see few other error codes on your Coleman Lazy Spa control panel like lazy spa E08, lazy spa E03, And lazy spa E02. You can troubleshoot all the error codes by pressing the lay z spa thermal reset button which you will find at the side of the lazy spa heater.

What does E03 mean on Coleman saluspa hot tub?

E03 error code: 1,Turn on the treadmill , motor running a few seconds then stop and console board shows E03, probably the Speed sensor issue. What does eo1 mean on hot tub?

How do I fix error code E02 on a lazy spa?

Jim Brown

How do I fix error code E02 on a lazy spa?

Please follow these steps to resolve this:

  1. Remove the spa pump from the liner, with the stopper caps placed on the inside.
  2. Empty the spa fully of water.
  3. Remove the stopper caps and place a hose on the inside of the spa, up against the debris screen.
  4. Complete this for 5 minutes on each debris screen.

How do I reset my lazy spa E02?

Pump needs to be reset.

  1. Watch the Thermal Reset Video.
  2. Turn the pump unit on at the mains.
  3. Press the test button once and leave it bleeping (leave for 10 seconds).
  4. Turn the pump unit off and unplug from the socket (leave for 10 seconds).
  5. Plug the pump unit back in and turn it back on.

How do you fix the code on a hot tub?

DR or DRY Error Message Like FLO issues, this can commonly be fixed by topping off your hot tub water level. DR or DRY will show up if there is little to no water travelling through your heater.

Where is the reset button on my lazy spa?

How do you reset a lazy spa?

  1. Plug back in and switch on. Then wait 10 seconds. [
  2. Press the test button once and leave it beeping for. [ 01:19]
  3. Turn off plug and remove from socket then wait 10 seconds. [ 01:27]
  4. Fully depress the thermal reset button. This is found on the side of the pump next to a yellow sticker. [

What does E03 mean on hot tub?

AMBIENT AIR TEMPERATURE
E03 ERROR CODE AMBIENT AIR TEMPERATURE. REASON, THE TEMPERATURE IS TOO LOW. This error code is visible if the ambient air temperature is too low outside. The spa pump will not run if the air temperature is below 4-6°c.

Why does my hot tub keep beeping?

Have you changed your filter recently? A dirty filter will block the water from circulating your filter housing and a safety cut off valve will kick in to avoid breaking the pump displaying warning E02. This is one of the main causes of the alarm being set off.

How do I reset my hot tub heater?

How Do I Reset My Hot Tub Heater?

  1. Turn off the power to your hot tub at the breaker.
  2. Find your hot tub’s red high limit reset button, which may be on the heater itself covered by rubber.
  3. Next, press the red reset button, which will make a clicking sound when it has been reset.

What does Dy code mean on hot tub?

In our experience one of the most common error codes is “The Heater May Be Dry”, or “OHH”, “DY”, “DR” or similar depending on your model of hot tub. WHAT CAUSES THIS ERROR CODE? In most cases, the error is being caused by dirty or clogged filters, and often filters that are just plain old and need to be replaced.

Why does my hot tub keep saying E02?

Furthermore, what does e02 mean on hot tub? E02 means that the system does not detect the water flow. Unplug the pump, then plug pump back in, next put one hand in front of the upper valve inside the spa , then press the Water Filter Button to check if there is any water flow.

What is the lazy spa error code E02?

If you are curious about what is Lazy Spa E02 and how to fix Lazy Spa Error Code E02? Here is your answer This is an error code which displays on the control panel of Lay z Spa due to lay z spa pump problems. Here are some common Reasons Why Lazy Spa E02 And Lazy Spa E08 occur:

When do I get the E02 error code?

The E02 error code can occur when the filters are dirty or blocked. SOLUTIONS WASH OR CHANGE THE FILTERS Remove the filter cartridge from the filter housing. Using luke warm water, run the filter cartridge under the water until it runs clear.

What does EO2 mean on a hydrojet hot tub?

Published on Aug 8, 2018. The EO2 error can affect all AirJet™ and HydroJet™ Lay-Z-Spa hot tubs. There are a number of causes which can be fixed quickly and easily. Cause 1: Dirty filter. A dirty water filter can cause water flow issues resulting in an EO2 error.

https://www.youtube.com/watch?v=NtAnfS65jnA

How do I fix error code E02 on a lazy spa?

Jim Brown

How do I fix error code E02 on a lazy spa?

Please follow these steps to resolve this:

  1. Remove the spa pump from the liner, with the stopper caps placed on the inside.
  2. Empty the spa fully of water.
  3. Remove the stopper caps and place a hose on the inside of the spa, up against the debris screen.
  4. Complete this for 5 minutes on each debris screen.

How do I reset my lazy spa E02?

Pump needs to be reset.

  1. Watch the Thermal Reset Video.
  2. Turn the pump unit on at the mains.
  3. Press the test button once and leave it bleeping (leave for 10 seconds).
  4. Turn the pump unit off and unplug from the socket (leave for 10 seconds).
  5. Plug the pump unit back in and turn it back on.

How do you fix the code on a hot tub?

DR or DRY Error Message Like FLO issues, this can commonly be fixed by topping off your hot tub water level. DR or DRY will show up if there is little to no water travelling through your heater.

What does E03 mean on hot tub?

AMBIENT AIR TEMPERATURE
E03 ERROR CODE AMBIENT AIR TEMPERATURE. REASON, THE TEMPERATURE IS TOO LOW. This error code is visible if the ambient air temperature is too low outside. The spa pump will not run if the air temperature is below 4-6°c.

Why does my hot tub keep beeping?

Have you changed your filter recently? A dirty filter will block the water from circulating your filter housing and a safety cut off valve will kick in to avoid breaking the pump displaying warning E02. This is one of the main causes of the alarm being set off.

What does E02 mean on a hot tub?

E02 After starting or during the functions of filtering or/and heating, the water flow sensors do not detect water flow. 1. The 2 stopper caps have not been removed from inside the spa. Remove the filter set from inside the spa and push the filter or heat button. What does e03 mean on hot tub? E03 means that the water temperature is lower than 4ºC.

Why does my hot tub keep beeping and cutting out E02 warning?

This is more relevant for Lay-Z-Spa hots tubs although other brands do have this fault function. The pump housing displays an E02 warning which will cut off the pump and heating system, or the housing just cuts out altogether. TOP TIP: Reset the device after you try each common issues below for E02! Have you changed your filter recently?

What does EO2 mean on a hydrojet hot tub?

Published on Aug 8, 2018. The EO2 error can affect all AirJet™ and HydroJet™ Lay-Z-Spa hot tubs. There are a number of causes which can be fixed quickly and easily. Cause 1: Dirty filter. A dirty water filter can cause water flow issues resulting in an EO2 error.

What to do if your hot tub has an E11 error code?

Gradually add and dissolve 0.5kg (500g) of Pure Spa Salt at a time. Start the Salt Chlorinator System. Allow the spa pump to run on either the 5 hour or 8 hour setting. If the E11 error code is visible again, place a further 0.5kg (500g) of Pure Spa Salt in the spa. Water Leakage.

https://www.youtube.com/watch?v=NtAnfS65jnA