Menu Close

How do you start a Poulan chainsaw?

Jim Brown

How do you start a Poulan chainsaw?

How to Start a – Simple 7 Steps Guide

  1. Step 1: Remove The Bar Cover. Before doing anything you need to remove the bar cover.
  2. Step 2: Activate The Chain Brake.
  3. Step 3: Move The Choke Lever.
  4. Step 4: Turn The Switch On.
  5. Step 5: Depress The Primer Bulb.
  6. Step 6: Position The Chainsaw.
  7. Step 7: Pull The Starter Rope.
  8. Flooded Engine.

Why does my Poulan chainsaw not start?

If your Poulan chain saw won’t start, the first thing to check is the fuel. Then turn the saw on, hold it firmly and pull the start rope in short, brisk pulls until it starts. If it doesn’t start within 15 pulls, the spark plug is likely wet-fouled. Remove it and check for moisture on the electrode.

What chain does a Poulan PL3314 use?

Powered by a 33cc 2-cycle gas engine, the PL3314 is equipped with a 14 in. steel bar and chain. Lightweight and perfect for cutting firewood and tree limbs around the house.

What size fuel line does a Poulan chainsaw use?

The 4218 uses 3/32″id by 3/16″od and . 080″ id by . 140″od fuel lines .

Why is my Poulan chainsaw smoking?

An abundance of smoke emanating from the engine often indicates that an excessive amount of oil has been introduced into the oil and gasoline mixture that powers the chain saw. Empty the fuel tank of all the oil and fuel mixture and fill the tank with the newly mixed fuel and oil before using the chain saw again.

How long do Poulan chainsaws last?

Re: Poulan Pro Chainsaws Most of those discount saws have about 40 hours expected useful life built in to them. Stihl’s, in comparison, are either 500 or 1000, depending on the model.

How do you troubleshoot a Poulan chainsaw?

Poulan Pro Chainsaw Troubleshooting

  1. Make sure you are starting the engine properly.
  2. Fill the tank with the correct fuel mixture.
  3. Clean the saw blade.
  4. Check the fuel line for kinks or leaks.
  5. Replace the fuel filter.
  6. Clean the air filter.
  7. Remove and replace the spark plug.

What should I do before starting a Poulan chainsaw?

After consulting your owner’s manual, the first thing you should do is to check the fluid levels on your chainsaw and ensure that all of the fluids have been filled and are in the correct proportions. Once that has been accomplished, move the choke so that it is in the “full” position.

Where is the chain brake on a Poulan chainsaw?

It is now time to start your Poulan Chainsaw. Before doing anything you need to remove the bar cover. You will then need to activate the chain brake by pressing on it. It is located at the top handle. When the chain brake is activated. You will move the choke lever to the full position.

What’s the primer bulb on a Poulan chainsaw?

If the Poulan Chainsaw you own has an on/off switch. You only need to move the switch to the on position. It is mostly indicated by the symbol “I” and not “O”. If your Poulan Chainsaw has a primer bulb. You will press it 4-5 times to draw fuel to the carburetor.

Why does my Poulan chainsaw have no spark?

Spark plugs ignite sparks in chainsaws. A faulty spark plug equals no spark and no start. A way to know the spark plug is defective is when you notice that it is corroded (most times, it looks burnt and the porcelain layer is cracked).

How do you start a Poulan chainsaw?

Jim Brown

How do you start a Poulan chainsaw?

How to Start a – Simple 7 Steps Guide

  1. Step 1: Remove The Bar Cover. Before doing anything you need to remove the bar cover.
  2. Step 2: Activate The Chain Brake.
  3. Step 3: Move The Choke Lever.
  4. Step 4: Turn The Switch On.
  5. Step 5: Depress The Primer Bulb.
  6. Step 6: Position The Chainsaw.
  7. Step 7: Pull The Starter Rope.
  8. Flooded Engine.

Why does my Poulan chainsaw not start?

If your Poulan chain saw won’t start, the first thing to check is the fuel. Then turn the saw on, hold it firmly and pull the start rope in short, brisk pulls until it starts. If it doesn’t start within 15 pulls, the spark plug is likely wet-fouled. Remove it and check for moisture on the electrode.

How good is a Poulan chainsaw?

Even though Poulan chainsaws share a lot of the same technology as their Husqvarna cousins, they tend to be a lot cheaper. This makes the Poulan Pro range of chainsaws excellent value for money. For the average homeowner, Poulan Pro chainsaws are a good mid-level quality that will get the job done around the yard.

How do you troubleshoot a Poulan chainsaw?

Poulan Pro Chainsaw Troubleshooting

  1. Make sure you are starting the engine properly.
  2. Fill the tank with the correct fuel mixture.
  3. Clean the saw blade.
  4. Check the fuel line for kinks or leaks.
  5. Replace the fuel filter.
  6. Clean the air filter.
  7. Remove and replace the spark plug.

How long should a Poulan chainsaw last?

Re: Poulan Pro Chainsaws To make up for the low price they may have lower quality parts, especially internal engine parts. Most of those discount saws have about 40 hours expected useful life built in to them.

How to adjust the L and h on a Poulan chainsaw?

Adjust the L screw to get the saw to idle correctly.the other screw that adjust the idle speed may also require adjustment Note: If you turn in the H screw beyond one turn from seat,you are starving the cylinder for gas and oil mixture and can sieze the saw !

Can a spark plug be checked on a Poulan chainsaw?

The spark plug needs to be checked to ensure spark is produced. You can do this by holding the rubber boot of your Poulan pro Chainsaw spark plug and grounding the other end on the metal of your chainsaw engine. If there is no spark the spark plug might be defective.

What causes a Poulan Pro saw to stall?

An engine that idles too fast can force the chain to spin unexpectedly while engines that idle too slowly will stall. Put on your gloves and take your Poulan Pro saw to a clear area with level ground.

Why does my 2150 Poulan chainsaw not start?

Hi, my 2150 Poulan chainsaw will start up but not run more than 1 minute. Then when i try to start it back up it is either flooded or isn’t getting enough gas? I don’t know. I bought a new plug, cleaned the arrestor, soaked the carb. in cleaner overnight, and was fiddling with the L and H.