Menu Close

How do I reset my Jeep?

How do I reset my Jeep?

The process takes about 20 seconds for you to complete in case they forget to reset the light.

  1. Turn the ignition switch to the “ON” position without starting the vehicle.
  2. Press the gas pedal to the floor slowly three times within 10 seconds. Turn the ignition off. Wait 10 seconds and start the engine.

How do I reset my Jeep JK Wrangler?

Resetting the Jeep Wrangler UConnect Radio System

  1. Start your vehicle and press down on the ‘voice recognition’, and ‘phone’ buttons located on the steering wheel.
  2. Turn off your vehicle and wait for the UConnect display to go completely black.
  3. Afterwards, open and close the driver’s door and restart the vehicle.

How do you reset the code on a Jeep Wrangler?

How to Clear Codes on Jeep Wrangler

  1. Make sure the engine is not running and key is out of the ignition.
  2. Disconnect the battery terminals.
  3. Wait 5 minutes.
  4. Reconnect battery terminals.
  5. Insert and turn the ignition key to the run position without starting.
  6. All error codes are cleared and CHECK ENGINE icon disappeared.

How do I reset my Jeep PCM?

New Member

  1. Disconnect the POSITIVE battery Terminal and touch it to ground for 30 seconds to discharge the PCM capacitors, which maintain the Adaptive Memory.
  2. Reconnect the Battery Cable.
  3. Turn Ignition Switch to the “On” position but DO NOT start the engine.
  4. Turn Headlight On.
  5. Turn Headlights Off.
  6. Turn Ignition Key Off.

How many miles does it take to reset a jeep computer?

For good measure. Anytime that you reset your Jeep PCM you should keep in mind that you will need to drive your car for approximately 10-15 miles so your Jeep ECM can re-learn your driving habits and fuel management.

Why isn’t my screen working in my Jeep?

The Jeep Grand Cherokee touchscreen not working can be due to multiple different things such as a short or disconnected power cable under the dash, a software glitch or issue, and it could also be a blown fuse or damage to the screen.

How do I calibrate my Jeep Wrangler touch screen?

Hold the up, down, and front defrost buttons simultaneously for about 5 seconds and then you are presented with the “Dealer Mode” menu. – Hold down the up, down, and Browse/Enter buttons simultaneously for about 5 seconds. That puts you into touchscreen calibration mode.

How do you diagnose a bad PCM?

7 Common PCM Failure Symptoms

  1. Your ‘Check Engine’ Light is On.
  2. Your Car Won’t Start or Starts Roughly.
  3. Sudden Loss of Gas Mileage.
  4. You Failed Your Emissions Test.
  5. Your Engine Stutters or Stalls.
  6. Erratic or Random Shifting.
  7. You’re Receiving a PCM-Related Error Code.
  8. What to Do If You Experience PCM Failure Symptoms.

What are the symptoms of a bad PCM relay?

The failed PCM relay will turn off the dashboard lights and other key safety warning lights that are normally illuminated when you turn the key in the ignition. Furthermore, and more importantly, the vehicle will usually be unable to start and it might be impossible to turn the key.

How to reset the radio on a Jeep Wrangler?

If it’s the original Jeep radio, the only way to reset is to disconnect from power for 5+ minutes, then hook it back up. You can emulate this by disconnecting the battery for the same amount of time, then reconnecting it. Sounds like you did that already with no luck.

How to clear check engine light on Jeep Wrangler?

How to Clear Codes on Jeep Wrangler 1 Make sure the engine is not running and key is out of the ignition 2 Disconnect the battery terminals 3 Reconnect battery terminals 4 Insert and turn the ignition key to the run position without starting. 5 All error codes are cleared and CHECK ENGINE icon disappeared. …

How to reset your Jeep engine control module?

3- Once the time has passed you should now turn the headlights “on” and “off” twice to drain the Engine Control Module from any remaining power. 4- Now plug back in the negative terminal and your Jeep ECM should now be reset. To finish off this post , here are a couple of things you should keep in mind.

How to reset JL Uconnect 4 system, 2018 + Jeep?

1) Hold hot and cold physical buttons on the dash at the same time for 5 seconds when the car is running. 2) Select “Reset to Factory Defaults”. Oviously all settings, pairing, radio stations etc will be lost. EDIT: Word of warning, there’s a risk of loosing Navigation.