Menu Close

How do you adjust motorcycle headlights?

Jim Brown

How do you adjust motorcycle headlights?

Sit on the motorcycle, holding it straight, with the headlight pointed straight ahead and the front tire on your masking tape mark. The low beam’s upper cutoff line should align with the lower piece of masking tape. The high beam should align with the upper piece of masking tape.

How high should motorcycle headlights be?

When aiming the headlights, the lens should be 10 feet from a vertical wall, 20 feet is better. 1. Measure the distance from the ground and the center of the headlamp (lamp height).

How high should headlights be off the ground?

Headlight Height Requirements The follow states mandate that headlight height be between 24 and 54 inches from ground level: Alaska, Arkansas, Washington DC, Indiana, Kansas, Louisiana, Maine, New Mexico, New York, Oklahoma, Oregon and Texas. Colorado mandates a maximum light height (44 inches), but not a minimum.

How much does it cost to get headlights aligned?

The average cost for headlamp alignment adjust is between $40 and $50. Labor costs are estimated between $40 and $50. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed.

How do you properly aim your motorcycle headlight?

How do you properly aim the headlight on your motorcycle? Adjust your motorcycle headlight in three phases. First, you set up the target area to determine where to locate the light. Next you adjust the light. Last, double check the high and low beams.

Where are the passing lights on a motorcycle?

Many cruisers have over one headlight at the front of the motorcycle. If you look closely, you may find two additional lights, one on each side, of the main lamp. We know these additional lights as passing lights. Sometimes the bike will come from the factory with the passing lamps already installed.

What’s the best way to aim a motorcycle?

Step 3. Place your motorcycle 25-30 feet away from the wall. You want to give yourself some distance to see how the adjustments you make affect the beam. A few articles will tell you specifically to place the motorcycle 25 feet away from the wall.

Where do you put the low beam on a motorcycle?

Switch on the headlights and mount the motorcycle. The low beam’s upper cutoff point should rest right on the lower line. Because most bikes have combined high- and low-beam reflectors, setting the height (and checking to see that the beam is centered along the bike’s long axis) is about all there is to it.

How do you adjust motorcycle headlights?

Jim Brown

How do you adjust motorcycle headlights?

Sit on the motorcycle, holding it straight, with the headlight pointed straight ahead and the front tire on your masking tape mark. The low beam’s upper cutoff line should align with the lower piece of masking tape. The high beam should align with the upper piece of masking tape.

How do you tell if your headlights are aimed correctly?

The top of the low beam shining on the wall should be at or slightly below the height of the center of the headlight lens for most vehicles. You should expect the light pattern to be higher on the right side (passenger side) to illuminate road signs and lower on the driver’s side to prevent blinding other drivers.

What is the correct headlight beam adjustment?

Clockwise turns should raise the lights, while counterclockwise turns should lower the lights. Turn the headlights on after adjusting and look at the light pattern on the wall. The top of the most intense part of the beam should be even with, or just below the center of the line of tape you made.

Can headlights be aimed too high?

If your headlights are pointed at the ground it causes glare on the road which negatively affects your ability to see far down the road. If your headlights are aimed a little too high they could be shining into space reflecting off nothing rendering them practically useless!

How do you adjust the headlight on a motorcycle?

If your bike is within the tolerances then the next step is to check your beams positioning against the vertical zero percent line. If not, adjust your headlight beam until it does fall within tolerance. Most motorcycles have a knob at the back of the headlight unit allowing for easy adjustment.

Do you need to adjust the beam pattern of Your Headlights?

No matter how easy modern headlight replacement kits make installation, there are a few critical skills every do-it-yourselfer need to know — such as how to aim headlights. Once your retrofit is complete, you’ll almost always find that the beam pattern needs to be adjusted.

Where do you put the low beam on a motorcycle?

Switch on the headlights and mount the motorcycle. The low beam’s upper cutoff point should rest right on the lower line. Because most bikes have combined high- and low-beam reflectors, setting the height (and checking to see that the beam is centered along the bike’s long axis) is about all there is to it.

How to adjust headlights for the perfect aim?

TRS Tips: How to Adjust Headlights for the Perfect Aim! If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.