Menu Close

How many coats of Drylok should I do?

Jim Brown

How many coats of Drylok should I do?

A minimum of 2 coats is required for the fully transferable warranty to apply. Now, inspect the surface for any remaining pinholes and fill them in. If it still leaks, a random pore or pinhole is still open.

Is Drylok bad for basement walls?

DO NOT PAINT YOUR WALLS, even with Drylok or waterproofing paint. Also, do not attach insulation directly to the foundation walls. It behaves as a moisture trap and can also hide structural problems and cracks in the foundation. Bottom line: basement walls need to breathe too.

How many sq ft does a 5 gallon bucket of Drylok cover?

Sizes: quart, gallon, 5 gallon. Coverage: 75-100 square feet per gallon. No pre-mixing or pre-wetting.

Does Drylok need 2 coats?

Two coats of DRYLOK® Original Basement & Masonry Waterproofer are required to assure warranted waterproofing.

Can you apply DRYLOK with a sprayer?

Latex Base DRYLOK® Masonry Waterproofer can be applied by spraying to exterior and interior masonry structures, providing certain precautions are followed. The key to obtaining satisfactory waterproofing is to be sure a continuous film of waterproofer is applied.

Will Drylok kill mold?

While Drylok is designed to prevent water from penetrating through foundation walls, it will not remove existing mold or mildew. Simply ignoring the problem and painting straight over it is not recommended as it can only prevent further fungus from growing.

Can I put DRYLOK over old DRYLOK?

DRYLOK is not warranted when used over previously painted surfaces or on horizontal surfaces. DRYLOK EXTREME may be applied over surface previously painted with Latex Base DRYLOK Masonry Waterproofer or Oil Base DRYLOK Masonry Waterproofer.

Can you apply DRYLOK over old DRYLOK?

Yes and no. DRYLOK® may be used over any other cementitious-type waterproofing paint in good, repaintable condition, either inside or outside. DRYLOK® Latex Concrete Floor Paint and DRYLOK® E1 1-Part Epoxy Floor Paint can be applied over previously painted surfaces.

How many square feet does a drylok cover?

A. Both DRYLOK ® Original Masonry Waterproofer and DRYLOK ® Extreme Masonry Waterproofer cover 75-100 square feet per gallon, and DRYLOK ® Floor & Wall Masonry Waterproofer covers 90-100 square feet per gallon, depending on the porosity of the surface.

How long does it take UGL drylok to dry?

Dry time: 2-3 hours Coats: minimum of 2 for Warranty Coverage to apply Recoat time: 2 hours After 24 hours, DRYLOK ® will accept a decorative topcoat using a good quality latex paint

Can a drylok extreme be used on a floor?

A. DRYLOK® Extreme and DRYLOK® Latex Base Masonry Waterproofers are not formulated for floors. You can use DRYLOK® Clear Masonry Waterproofer on floors and walls. It holds up to foot traffic as a finished coat and can be used before applying floor paint, or latex-based adhesives.

How long is drylok original masonry waterproofer good for?

A. When applied according to directions, DRYLOK® Original Masonry Waterproofer is warranted for 10 years, DRYLOK® Extreme Masonry Waterproofer is warranted for 15 years, and DRYLOK® Floor & Wall Masonry Waterproofer is warranted for 7 years. In many instances, these products will provide many additional years of satisfactory performance.

How many coats of Drylok should I do?

Jim Brown

How many coats of Drylok should I do?

A minimum of 2 coats is required for the fully transferable warranty to apply. Now, inspect the surface for any remaining pinholes and fill them in. If it still leaks, a random pore or pinhole is still open.

How long does Drylok need to dry before rain?

Dry time: 2-3 hours. Coats: minimum of 2 for Warranty Coverage to apply. Recoat time: 2 hours. After 24 hours, DRYLOK® will accept a decorative topcoat using a good quality latex paint.

How long does it take for Drylok to set up?

Dry time: 2-3 hours. Coats: minimum of 2 for Warranty Coverage. Recoat time: 2-3 hours. Optional: After 24 hours, DRYLOK® Original Masonry Waterproofer may be topcoated with a good quality latex paint for decorative purposes.

Can Drylok be applied to wet walls?

DryLok is a useful coating which can be painted onto wet basement walls to protect them from damage. It is available in powdered form and ready mixed, which can simply be painted straight onto the wall. DryLok is not only suitable for wet basements, but it’s also commonly used in birdbaths and fish ponds.

What temperature should I apply DRYLOK?

DO NOT THIN. Paint only when air and surface temperatures are 50°F (10°C), or higher. Apply first coat directly on bare masonry using a roller (3/4” nap), DRYLOK® Brush, or a good quality nylon bristle brush, or sprayer.

Can you use DRYLOK over old paint?

Can DRYLOK® be used over paint? A. No, you need to remove any existing coating. DRYLOK® works by entering the pores of the masonry and expanding as it dries to become part of the wall surface.

Does DRYLOK paint really work?

The UGL Drylok Extreme system is guaranteed to work for up to 15 feet of head or water pressure and for up to 15 years. It is not a crystalline system—it’s more paint-like—although the manufacturer states that it does penetrate the concrete. A double-coating of UGL Drylok Extreme that still weeps water.

How do you prepare walls for DRYLOK?

DRYLOK paint should only be applied after you prep walls by cleaning them with a wire brush, removing salt deposits and sealing cracks and holes. Paint the walls when the temperature is at least 50 degrees Fahrenheit, optimally during a rain-free period when humidity levels are not high.

How long does it take for drylok to dry?

If you prefer to use a roller, be sure to back brush the first coat to make sure DRYLOK ® penetrates those pores and pinholes. After three hours, the first coat will be dry. Apply coat number two using your choice of a roller, brush, or sprayer. A minimum of 2 coats is required for the fully transferable warranty to apply.

How long does it take for a coat of paint to dry?

The “recoat time” is the how long paint must dry before it’s okay to apply another coat of paint. The more coats of paint you apply, the longer this recoat time might be, but early recoat times tend to be one to two hours.

How long does it take to paint a drylok fast plug?

The patched area may be smoothed and trimmed to the surrounding area in approximately 5 minutes. DRYLOK ® Fast Plug ® may be painted when set with DRYLOK ® Original Masonry Waterproofer , DRYLOK ® Extreme Masonry Waterproofer, DRYLOK ® Powdered Masonry Waterproofer or DRYLOK ® Concrete Floor Paint.

When to apply a second coat of drylok?

After the first coat of Drylok has dried, it will be dry to the touch, apply a second coat. Make sure you follow the recommended drying time on the Drylok container.