Menu Close

How thick should thinset be under Ditra?

Jim Brown

How thick should thinset be under Ditra?

Thinset between tile and Ditra will come in at approx 1/8″. Ditra with thinset over the sub-floor, maybe slightly more the 1/8″ – call it 5/32″.

What thinset do you use for Ditra?

What type of thin-set mortar should I use when setting tile over Schluter™-DITRA and Schluter™-DITRA-XL? Schluter-Systems requires the use of Schluter SET™ , ALL-SET™ , FAST-SET™, or an unmodified thin-set mortar meeting the requirements of ANSI A118. 1 to install ceramic.

What thickness does thinset add?

The terms thinset cement, thinset mortar, dryset mortar, and drybond mortar are synonymous. This type of cement is designed to adhere well in a thin layer – typically not greater than 3/16th thick. For example, a 3/8″ notch trowel will produce a 3/16th inch thick coating after the tiles are pressed in to the cement.

Is DITRA better than cement board?

1. Ditra is waterproof, while cement board lets water through but won’t be damaged by it. This may make Ditra a better choice if moisture from below is a concern, such as with some outdoor applications or installations over concrete. Some tile setters also prefer Ditra for its relatively quick installation.

How thick is DITRA after installation?

DITRA is 1/8″ (3 mm) thick, which minimizes tile assembly thickness and reduces transitions to lower surface coverings (e.g., carpet, engineered wood, and vinyl).

What size trowel do I use for DITRA?

For DITRA use a 1/4″ x 3/16″ (6 mm x 5 mm) V-notched trowel, 5/16″ x 5/16″ (8 mm x 8 mm) V-notched trowel, or the DITRA trowel, which features an 11/64″ x 11/64″ (4.5 mm x 4.5 mm) square-notched design, is recommended.

Can I use thinset as a floor leveler?

You can use thinset to install tile over an uneven cement floor and leave the floor perfectly level. You can also use thinset mortar to level out an uneven cement floor or fill small holes in the floor without installing tile.

How much thinset do I need for Ditra?

Ditra is 1/8″ thick, and can be installed on single layer plywood or OSB subfloors that are over joists spaced up to 19.2″ on center. Most common tile floor underlayments are 1/4″ thick, so Ditra is a great alternative if a shorter underlayment is needed. Subsequently, question is, how much thinset do I need for Ditra?

What’s the thickness of a Ditra floor underlayment?

Ditra is 1/8″ thick, and can be installed on single layer plywood or OSB subfloors that are over joists spaced up to 19.2″ on center. Most common tile floor underlayments are 1/4″ thick , so Ditra is a great alternative if a shorter underlayment is needed.

How much thin-set mortar will be used with Schluter®-Ditra?

To bond DITRA and DITRA-XL to the substrate: Use one 50 lb. (22.68 kg) bag of mortar per 150 – 200 ft 2 (13.9 – 18.6 m 2 ). To bond tile to DITRA, using a 1/4″ x 3/8″ (6 mm x 10 mm) square- or U-notched trowel: Use one 50 lb (22.68 kg) bag of mortar per 40 – 50 ft2 (3.7 – 4.6 m 2 ).

Which is notch trowel to use for Ditra?

The manufacture of the tile as well as the tile size generally has a rule of thumb in regards to what size notch trowel you should use, which in turn will give you a general idea of the thin set thickness, than it’s a matter of doing the math to decide which thickness of ditra to use.

How thick should Thinset be under DITRA?

Jim Brown

How thick should Thinset be under DITRA?

Thinset between tile and Ditra will come in at approx 1/8″. Ditra with thinset over the sub-floor, maybe slightly more the 1/8″ – call it 5/32″.

Is DITRA-HEAT an uncoupling membrane?

DITRA-HEAT provides uncoupling through its geometric configuration, which allows for in-plane movement that effectively neutralizes the differential movement stresses between the substrate and the tile, thus eliminating the major cause of cracking and delaminating of the tiled surface.

Can DITRA-HEAT go under cabinets?

The DITRA-HEAT heating cables cannot be installed under vanities with no air space beneath, bathtub platforms, free standing bathtubs with no air space beneath, kitchen cabinets and islands, appliances, or any other fixtures, or in small storage or clothing closets where various items may be kept on the floor.

Can you use modified thinset over DITRA-HEAT?

In general, we don’t recommend the use of modified thin-set mortar to set tile over the membranes because these mortars must air dry to cure properly. Therefore, extended cure times would be required before grouting if using modified thin-set mortars between DITRA and ceramic tile, including porcelain tile.

How thick is Schluter DITRA installed?

1/8″
DITRA is 1/8″ (3 mm) thick, which minimizes tile assembly thickness and reduces transitions to lower surface coverings (e.g., carpet, engineered wood, and vinyl).

What size trowel do you use for DITRA heat?

For DITRA use a 1/4″ x 3/16″ (6 mm x 5 mm) V-notched trowel, 5/16″ x 5/16″ (8 mm x 8 mm) V-notched trowel, or the DITRA trowel, which features an 11/64″ x 11/64″ (4.5 mm x 4.5 mm) square-notched design, is recommended.

Can you walk on Ditra heat?

Pro-Tip: DITRA can be walked on immediately after; there’s no need to wait for the mortar to cure.

Can you cut Ditra heat?

The DITRA-HEAT-E-HK heating cable is selected according to the size of the area to be heated. The heating cable cannot be cut to fit or installed under fixtures in the event that it does not fit the application. Cutting the cable will change the resistance and could result in cable damage or fire.

How big is the stud on a Ditra heat?

DITRA-HEAT is a polypropylene membrane with a cut-back stud structure and an anchoring fleece laminated to the underside. The thickness of the mat, including the stud structure is 1/4″ (5.5 mm). DITRA-HEAT-DUO is a polypropylene membrane with a cut-back stud structure and a thermal break anchoring fleece laminated to the underside.

What’s the thickness of a Ditra floor underlayment?

Ditra is 1/8″ thick, and can be installed on single layer plywood or OSB subfloors that are over joists spaced up to 19.2″ on center. Most common tile floor underlayments are 1/4″ thick , so Ditra is a great alternative if a shorter underlayment is needed.

How big is a Schluter Ditra heat duo?

The thickness of the mat, including the stud structure is 1/4″ (5.5 mm). DITRA-HEAT-DUO is a polypropylene membrane with a cut-back stud structure and a thermal break anchoring fleece laminated to the underside. The thickness of the mat, including the stud structure and thermal break fleece is 5/16″ (8 mm).

How much thinset do I need for Ditra?

Ditra is 1/8″ thick, and can be installed on single layer plywood or OSB subfloors that are over joists spaced up to 19.2″ on center. Most common tile floor underlayments are 1/4″ thick, so Ditra is a great alternative if a shorter underlayment is needed. Subsequently, question is, how much thinset do I need for Ditra?

How thick should thinset be under DITRA?

Jim Brown

How thick should thinset be under DITRA?

Thinset between tile and Ditra will come in at approx 1/8″. Ditra with thinset over the sub-floor, maybe slightly more the 1/8″ – call it 5/32″.

How do you know what size trowel to use?

Finding the right trowel for the job is quite simple when you know that, generally speaking, the trowel size should match up to the tile size – the smaller the tile, the smaller the trowel; the larger the tile, the larger the trowel.

What size notched trowel should I use?

All tile manufacturers offer a recommended trowel size. Mosaic installations up to 2 inches can use a 1/8-inch notch, as can wall tiles of up to 4 inches, as a general rule. 16-inch tiles need a 1/2-inch-deep notch, and anything over 24 inches should use a 3/4-inch notch.

Does thinset stick to DITRA?

While the membrane’s fleece IS bonded to the substrate, thinset does NOT stick to Ditra, and there are voids between the pillars that hold the tile up which means that if a lateral stress is applied, the whole tile and thinset layer can move totally independently of the subfloor or slab only restricted by the …

What thinset do you use with DITRA?

What type of thin-set mortar should I use when setting tile over Schluter™-DITRA and Schluter™-DITRA-XL? Schluter-Systems requires the use of Schluter SET™ , ALL-SET™ , FAST-SET™, or an unmodified thin-set mortar meeting the requirements of ANSI A118. 1 to install ceramic.

What size trowel should I use for 6×24 tile?

In general, the industry recommendation is to use a ¼” by ¼” U or square notched trowel for any tile larger than 16”. Both the tile manufacturer and the thin-set manufacturer may have recommendations on the size of the trowel.

Can thinset be used for leveling?

Thinset mortar is a type of cement used for the adherence of tiles and flooring to substrate, or subfloor materials. You can also use thinset mortar to level out an uneven cement floor or fill small holes in the floor without installing tile.

How thick should my thinset be?

The terms thinset cement, thinset mortar, dryset mortar, and drybond mortar are synonymous. This type of cement is designed to adhere well in a thin layer – typically not greater than 3/16th thick. For example, a 3/8″ notch trowel will produce a 3/16th inch thick coating after the tiles are pressed in to the cement.

What thinset do you use with Ditra?

What kind of trowel to use for Ditra?

For DITRA use a 1/4″ x 3/16″ (6 mm x 5 mm) V-notched trowel, 5/16″ x 5/16″ (8 mm x 8 mm) V-notched trowel, or the DITRA trowel, which features an 11/64″ x 11/64″ (4.5 mm x 4.5 mm) square-notched design, is recommended.

What size notched trowel should I use to install Schluter?

What size notched trowel should I use to install Schluter-DITRA and Schluter®-DITRA-XL? For DITRA use a 1/4″ x 3/16″ (6 mm x 5 mm) V-notched trowel, 5/16″ x 5/16″ (8 mm x 8 mm) V-notched trowel, or the DITRA trowel, which features an 11/64″ x 11/64″ (4.5 mm x 4.5 mm) square-notched design, is recommended.

How big of a trowel do I need for a 12 inch tile?

1/4″ x 1/2″ square notch: The 1/4″ x 1/2″ x 1/4″ square notch trowel is good for 12×12’s and 13×13’s maybe even up to 16×16’s no more than 3/8″ thick. 1/2″ x 1/2″ square notch: I use this trowel size for any large format tiles. 15 inches and larger.

Can a Ditra mat be used to install tile?

The Ditra Mat is now installed and you can immediately install floor tile on it. Installing tile on ditra mat is the same as most other tile substrates except that you must use the flat side of the trowel to fill the square holes on the top of the ditra with thinset before troweling on thinset with a notched trowel.

How thick should Thinset be under DITRA?

Jim Brown

How thick should Thinset be under DITRA?

Thinset between tile and Ditra will come in at approx 1/8″. Ditra with thinset over the sub-floor, maybe slightly more the 1/8″ – call it 5/32″.

What size notched trowel should I use?

All tile manufacturers offer a recommended trowel size. Mosaic installations up to 2 inches can use a 1/8-inch notch, as can wall tiles of up to 4 inches, as a general rule. 16-inch tiles need a 1/2-inch-deep notch, and anything over 24 inches should use a 3/4-inch notch.

How do you know what size trowel to use?

Finding the right trowel for the job is quite simple when you know that, generally speaking, the trowel size should match up to the tile size – the smaller the tile, the smaller the trowel; the larger the tile, the larger the trowel.

What thinset do you use with DITRA?

What type of thin-set mortar should I use when setting tile over Schluter™-DITRA and Schluter™-DITRA-XL? Schluter-Systems requires the use of Schluter SET™ , ALL-SET™ , FAST-SET™, or an unmodified thin-set mortar meeting the requirements of ANSI A118. 1 to install ceramic.

Can you walk on Ditra after install?

Pro-Tip: DITRA can be walked on immediately after; there’s no need to wait for the mortar to cure.

What kind of trowel to use for Ditra?

For DITRA use a 1/4″ x 3/16″ (6 mm x 5 mm) V-notched trowel, 5/16″ x 5/16″ (8 mm x 8 mm) V-notched trowel, or the DITRA trowel, which features an 11/64″ x 11/64″ (4.5 mm x 4.5 mm) square-notched design, is recommended.

What size notched trowel should I use to install Schluter?

What size notched trowel should I use to install Schluter-DITRA and Schluter®-DITRA-XL? For DITRA use a 1/4″ x 3/16″ (6 mm x 5 mm) V-notched trowel, 5/16″ x 5/16″ (8 mm x 8 mm) V-notched trowel, or the DITRA trowel, which features an 11/64″ x 11/64″ (4.5 mm x 4.5 mm) square-notched design, is recommended.

How big of a trowel do I need to install Durock?

1/8″ x 1/8″ notch trowel : Primarily a trowel to use for installing thinner membranes. After all, the Kerdi trowel is simply a 1/8×1/8″ notch trowel. Use it for installing kerdi, Valueseal, Hydroban sheet membrane, USG Durock shower membrane, etc.

How big of a trowel do I need for a 12 inch tile?

1/4″ x 1/2″ square notch: The 1/4″ x 1/2″ x 1/4″ square notch trowel is good for 12×12’s and 13×13’s maybe even up to 16×16’s no more than 3/8″ thick. 1/2″ x 1/2″ square notch: I use this trowel size for any large format tiles. 15 inches and larger.